10 Things We All Love About Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC windows are a great option for modern homes. They are durable, long-lasting and easy to maintain. They don't rot or rust like aluminum or timber.

It is important to clean and oil UPVC windows and doors on a regular basis. This will reduce repair costs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a great amount of damage to your home, which can make it very hazardous and possibly fatal. It is important to make sure that your windows are in good condition.

For single pane windows, it is fairly easy to replace them, and the new window is usually able to fit into the frame that was previously installed easily. However when you have double-pane windows that are held in place by internal beading, it'll be more difficult to remove the old panes and put in new ones. In this instance you'll need find some plastic spacers to aid the new pane in being able to fit correctly into the window frame.

Wearing protective eyewear and thick gloves is a must if you plan to remove the glass by yourself. You should also lay down a dropcloth prior to you begin working on the window repairs near me panes so that any shards fall onto the fabric and not onto the floor and could be trampled.

After the glass has been removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to prevent water and drafts from getting into the property until a professional comes out and fix the window. It also acts as an obstruction to prevent intruders from getting into your home. If the gap is particularly large, you may think about an alarm door that comes with an integrated window, as it offers the best of both worlds.

2. Sagging

uPVC is durable and energy efficient alternative to timber sash window. However, over time they can suffer from a variety of issues like sagging. A window that isn't properly aligned can cause problems with light, draughts, and even security. It's crucial to act when you notice your uPVC windows are falling down.

Repositioning the hinges could aid in fixing a window that is sagging. You'll first need to open the windows to reach the frame. With the screwdriver, you'll be able to take off the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. After you've repositioned the hinges, close the window and verify the fit. If you're satisfied with the size of the window, tighten the screws to keep them in the right position.

If you are unable to reposition the hinges, you may require replacing the seal. Rubber seals can dry out and lose their elasticity over time, leading them to lose their tightness. If this happens, it's crucial to replace the seal as soon as possible so that your uPVC windows are waterproof and secure from draughts.

uPVC handles may also become loose. This is typically caused by screws that have loosened over time, but it can also be due to the mechanism of the handle getting worn out. Luckily, it's not difficult to fix the handle of a window that is loose yourself. First, you'll need to close the window and perform a test fit. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't, you can make use of a screwdriver to loosen the handle and turn the mechanism back into position.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it is important that you take action. Water leaks from windows are not just a cause for degrading of the structure of your home but also hinder your efforts to regulate the temperature within your home. The most frequent reason for leaking uPVC windows is that the sealant surrounding the frame is either damaged or missing.

It is a fairly easy fix that can be completed by any skilled DIYer. Depending on how severe the issue is, old caulking might need to be removed. It is important to keep in mind that when it is about upvc window repair near me window repairs (your input here), do not be tempted to 'over-caulk' as this will only make the area harder to clean and reduce your energy efficiency.

Check that any drainage holes have no debris in them, and also that the sill pan is angled correctly to drain away from the window. In more serious situations, you might need to consider replacing the window.

Mold spots and rotten sills are other signs of water leakage. The fungus thrives in damp conditions and is able to quickly spread throughout the home.

If the leakage occurs between the double-glazed window, it is more likely the issue is with the seal rather than the frame. Again this can easily be repaired by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and open in a breeze it could be hinges at the fault. Any competent DIYer can replace the hinges in a matter of minutes.

Nearly every home in the UK will have top-hung or side hung uPVC windows that use hinges and, like all mechanical parts, they will wear out over time. It's very simple to replace a hinge on a window, but it's easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the right direction. This can be done by checking for the arrows on each hinge, this shows which way the window should open.

The problem can be caused either by opening the window improperly or a faulty installation in the factory. It is usually possible to fix the issue by sending us a photo through our website and we will be more than happy to give you advice.

It is also essential to grease the hinges regularly. Applying an engineering lubricant that is light to the hinges is an ideal method to accomplish this. We suggest using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It also helps prevent corrosion and reduce the risk of sticking. This should be done at least every year. WD40 or other solvent-based oils should not be used as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different causes. The hinges can also be misaligned due to wear, creating a gap where the sash and frame meet. This can be easily repaired by giving them a good clean, but when they're beyond repair, it may be necessary to get them realigned or replaced. The second is the interlock, which is located on the hinge side of the window, can also become misaligned, again it's possible to just give them a thorough clean, however in some cases it might be necessary to get them replaced.

These seals can wear down or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glass. This will help to regulate indoor temperatures and lessen the risk of draughts.

The final method to cut down on draughts effectively is by using a Draught-excluder. These are usually fabric tubes filled with a filler that can be hung over your window sill. They can keep your home warm by blocking out cold air.

Your windows made of upvc will continue to provide excellent insulation and security for your home with regular maintenance and repairs. It is essential to remember that all windows will eventually become worn out, and it could be more cost-effective to replace them than to repair them. If you have any problems with your upvc window you should consult a professional as soon as possible.